Vmware player network configuration11/23/2023 This will add back the NAT adapter and other builtin adapters that VMware workstation installs out of the box. This is to set the VMware workstation networks back to defaults. When looking into networking issues with VMware Workstation that can’t be explained by OS network misconfiguration or some other obvious network configuration problem, we can use a builtin mechanism to reset the network configuration in VMware Workstation. Troubleshooting VMware Workstation Network connectivity There is a simple way to get things working properly in VMware Workstation. What I have found in troubleshooting VMware Workstation network connectivity is that often the builtin networks get corrupted or due to misconfiguration or altering by end users they get deleted. If DHCP they fail to pull an IP address and static simply has no connectivity. Oftentimes, problems present in the fashion that VMs boot and show to be connected to respective networks, however, they have limited connectivity. From time to time, I have seen issues with VMware Workstation network connectivity either in Bridged or NAT’ed configuration. I also troubleshoot VMware Workstation for other users as well. unfortunately i’m not expert enough in VMware to know what that detail entails.Typically, I use VMware Workstation every day running work VMs and performing other testing. What i also believe happened is in so running the commands, the associated registries was renewed and cleaned up. but after running the commands, it was cleaned up. i noticed that before the above commands, it had several blank lines before the config lines started. Running the commands also actually updates the nf file and other files located in C:/ProgramData/VMware/. but just changing the VMnet8 was enough to also get VMnet1 working. It could be that the previous IP range it picked was already existing. Lots of comments and suggestions in other sites but nothing resolved it for me til i ran the commands above from the admin prompt. I had a newly installed VMW WKSTN 12 player on WIN7 Pro and any VM copied or created was giving me a “a duplicate name exists on the network” error with resulting Iprange of 169.254… even when no dupes exists. Here we see that the IP address of the Windows host will be 10.0.2.2- at least in so far as a VMWare guest running with NAT networking is considered. : 255.255.0.0Įthernet adapter VMware Network Adapter VMnet8: Some folks on the VMWare Community Forums have also provided some documentation for these command line commands.įrom an administrator prompt on the host, runĬ:\Program Files (x86)\VMware\VMware Player>vnetlib.exe - stop natĬ:\Program Files (x86)\VMware\VMware Player>vnetlib.exe - stop dhcpĬ:\Program Files (x86)\VMware\VMware Player>vnetlib.exe - set vnet vmnet8 maskĬ:\Program Files (x86)\VMware\VMware Player>vnetlib.exe - set vnet vmnet8 addrĬ:\Program Files (x86)\VMware\VMware Player>vnetlib.exe - set adapter vmnet8Ĭ:\Program Files (x86)\VMware\VMware Player>vnetlib.exe - set nat vmnet8Ĭ:\Program Files (x86)\VMware\VMware Player>vnetlib.exe - update dhcp vmnet8Ĭ:\Program Files (x86)\VMware\VMware Player>vnetlib.exe - update nat vmnet8Ĭ:\Program Files (x86)\VMware\VMware Player>vnetlib.exe - update adapterĬ:\Program Files (x86)\VMware\VMware Player>vnetlib.exe - start dhcpĬ:\Program Files (x86)\VMware\VMware Player>vnetlib.exe - start natĬ:\Program Files (x86)\VMware\VMware Player>ipconfigĮthernet adapter VMware Network Adapter VMnet1: It turns out that VMWare Workstation has a graphical tool that can be used to modify the network settings, but that tool does not come with VMWare Player.įortunately Leeland Artra ran across the problem as well, and provided instructions on how to make the change manually. Why do I care? The address range I use in the classroom laboratory for instructor demos is 10.0.2.0/24, (with a gateway at 10.0.2.254) so by using the same address space and gateway on VMWare as in the lab, I can simply copy the systems from one network to another without having to manually update all of the statically assigned IP addresses on each system. VMWare Player uses 192.168.75.0/24 for the NAT address range, and I would rather use 10.0.2.0/24. In VMWare Workstation, sure, there is a GUI tool to do this, but the situation in VMWare Player is more complex. There are times when you want to modify the settings for networking in VMWare Player.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |